Name
Description
Quantity
Price
ST1(sku: 9002)
PLASTIC FEET FOR KILN STAND
Help us to make sure we send you the right part and enter the model number and serial number of the kiln for which you need this part: Model Number: Serial Number:
$11.51
TF3 Relay 30 Amp(sku: 6355)
Relay, 30 amp, 12 volt coil. The relay sends power to the elements of digital kilns.
$47.75
TF40(sku: 6844-2)
CONTROL BOARD, SENTRY II, 2400 DEGREES F (CONE FIRE)
$522.58
TF2(sku: 6770)
TRANSFORMER 120/208/240V(UNIVERSAL)
$50.72
CR6(sku: CR6)
CORDSET, 50 AMP, 240 VOLT, NEMA 6-50, 6 FOOT
$93.79
BR1082(sku: BR1082)
BRICK BOTTOM FOR 82,81,88
$232.55
BP8 Full Formed Steel Base, 8 Sided Kilns(sku: 3005)
The full-formed steel base for 8-sided kilns. The base is made of long-lasting galvanized steel. It protects the firebrick kiln bottom. Install the steel base by removing the old one and sliding the tabs of the new one up behind the stainless steel case. Then fasten with screws.
$64.23
BR-B-8-3(sku: BR-B-8-3)
STRAIGHT, 2 GROOVE BRICK, 8 SIDE, 3" BRICK When ordering bricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
$24.98
BR-D-8-3(sku: BR-D-8-3)
TERMINAL BRICK 2 GROOVE, 8 SIDE, 3" BRICK When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
$26.24
BR-H-8-3(sku: BR-H-8-3)
PLAIN, NO GROOVE HALF BRICK, 8 SIDE, 3" BRICK When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
$13.35
BR11823(sku: BR11823)
LID FOR 82B-3. The lid comes with a band, but it does not include hardware such as the hinge and handle.
$289.12
EL8341111M(sku: EL8341111M)
ELEMENT, TNF823 MID 208V 5 OHM, 2 PER KILN
The element comes pre-stretched and bent at the wallbrick corners for a precise fit. Element connectors are included with each new element.
$123.95
EL8341111TB(sku: EL8341111TB)
ELEMENT, TNF823 T/B 208V 7 OHM, 2 PER KILN
$193.87
VENTMAST120, Not Installed(sku: VENTMAST120)
The patented Orton Vent Master not only vents fumes but also improves firing results.
It pulls fresh oxygen into the kiln for brighter colors, especially noticeable with red and orange glazes and decals. Fire red and green glazes in the same load without glaze contamination. The Vent Master draws air from the kiln, dilutes it with room air, and pushes it outdoors through a vent hose.
The extra oxygen and increased air movement help burn carbon out of the clay, which helps eliminate a host of firing problems: bloating, dark patches in the clay, porcelain mildew, pinholes, pitting, blisters, and bubbles.
The Vent Master removes fumes containing volatile metals, fluorides and sulphur oxides. You can fire even lusters, decals, metallics, and pate-de-verre glass without strong odor.
The flow of fresh air helps even out the temperature throughout the kiln. The vent also extends the life of the Kiln Sitter tube assembly, since fumes by-pass the tube. You will enjoy the convenience of the Vent Master. Throughout the firing, keep the lid closed and peephole plugs inserted. You no longer need to remember to lower the hot lid from vented position.
The Vent Master increases firing time by about five minutes for firings up to cone 4; 12 minutes for firings from cone 4 to 10. It has little effect on maximum temperature. At 132 watts, electrical consumption of the Vent Master motor is only pennies per firing.
From the shut-off temperature down to 1000°F, the Vent Master has little effect on cooling time. From 1000°F to room temperature, it reduces cooling time by about two hours.
As with Paragon kilns, the Orton Vent Master can be made for any electrical system in the world. Approved for use in the 1992 Uniform Mechanical Code. UL/CSA approved for UL Listed kilns. ETL Listed, CE Certified. Two year limited warranty.
The Vent Master requires a separate 120 volt wall plug unless your kiln is equipped with the AOP vent.
A 3’ long 2” duct comes with each vent. The 2” duct runs between the collection cup and the blower motor. Use 4” aluminum dryer duct or 4” PVC pipe between the motor and the vent outlet. (Do not use vinyl dryer duct.)
Position the Vent Master next to the kiln and attach the collection cup to the bottom or side of the kiln. The collection cup fits under most top-loading kilns. (Note: The kiln stand must be at least 5” high to accommodate the collection cup.) Since the vent motor is away from the kiln, there is no vibration in the kiln, the motor is kept away from the heat of the kiln, and the fan is easy to clean. The Vent Master works with all Paragon kilns except the smallest tabletop models. The Vent Master can vent two kilns. For the second kiln, order the Vent Master Expansion Kit.
Shipping dimensions: 15" wide x 10" deep x 12" high.
$757.38
PT-2 Protection Tube, S-Type Thermocouple(sku: 60032)
Ceramic protection Tube for S-type thermocouple, 2 1/2" - 3" (63 mm - 76 mm) wall kilns. Secure in the firebrick wall with a small amount of kiln cement.
$34.10
MS1 Porcelain Insulators(sku: MS1)
MS1 Porcelain Insulators, 1 1/8" long (28.57 mm). 4 per package. The insulators prevent the element from touching the kiln case.
$11.37
MS6 Element Connectors(sku: MS6)
MS6 Element Connectors, brass, 2 per package. Use new connectors when replacing an element. (Note: Paragon replacement elements come with new connectors.)
$10.52
TF5 Half Amp Fuse(sku: 6726)
TF5 Half Amp Fuse, AGC, 250V AC. This fuse protects the digital controller. The fuse is mounted in the kiln's control panel (usually on the side of the kiln).
$5.11
TF9 Fuse Holder for Switch Box of Digital Kilns(sku: TF9)
Fuse Holder for the kiln's AGC half amp fuse. The fuse holder is built into the kiln control panel (usually located on the side of the kiln).
TF71 Sentry Control Cable(sku: 6060-1)
TF71 12-key Sentry Control Cable. You will need this part when upgrading from the earlier DTC-series controllers to the Sentry 12-key or Sentinel Smart Touch.
$21.02
PL2 Peephole Plug Cone Shaped(sku: 2000)
PL2 Peephole plug, cone shaped. Keep a spare on hand in case you drop one. The plug is essential for kilns equipped with a downdraft vent.
$10.08
HW4 Small Lid Handle(sku: 1001)
Lid handle for small kilns, 8 sides or less.
$12.52
HW7 Prop-R-Vent(sku: HW7)
HW7 fall away Prop-R-Vent kit for top-loading kilns.
$23.03
PY80-4 Thermocouple (PY50)(sku: 6750-14)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge complete with ceramic block and lead wires for 2 1/2” - 3” wall kilns. (Order the PY81-4 if you do not need to replace the ceramic block or lead wires.) Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
$89.51
PY81-4 Thermocouple, K-Type, 2.5-3 inch Wall Kilns(sku: 60179-4)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge for 2 1/2” - 3” wall kilns (less ceramic block and wires). Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
$63.94
Sentinel Smart Touch Controller, replacement part(sku: 6844-71)
The Sentinel Smart Touch controller can replace the standard Sentry 2.0 12-key controller. The price shown here is for the Sentinel controller purchased for an existing kiln.
The Sentinel Smart Touch is made by Bartlett Instruments of Fort Madison, Iowa.
Ramp-Hold programs can have a customized program title, which is entered through the touch screen. Store 12 custom programs with up to 32 segments per program. The Sentinel includes Novice Mode, which adds questions to guide you during programming. The controller can be updated through WiFi. View the progress of a firing in graph mode. The firing schedule can be edited during firing with Skip Step, Add Segments, Add Temperature, and Add Time. The Sentinel can turn a kiln vent or gas injection flow meter on or off for each segment of a program.
$690.58
Rolling Stand Replacement Part, 18x18x12 inches(sku: SKU STD181812-BA)
The replacement stand for your Paragon 7- and 8-sided top-loading ceramic kiln has locking casters, a mounting bracket for the Orton Kiln Vent, and a greenware drying rack. (Take advantage of the heat that radiates from the kiln. Load greenware onto the lower shelf. Heat from the kiln will dry the ware for the next firing.) Roll the kiln out of the way when not using it. Ships unassembled. Assembly instructions included. This deluxe stand replaces the discontinued standard kiln stand. 18” square x 12” high. Ships in a 20” x 25” x 7” carton.
$195.53
Paragon Industries, L.P., 2011 South Town East Blvd. Mesquite, Texas 75149-1122 1-800-876-4328 Fax: 972-222-0646 Contact Us
Follow on:
Home
Support
Products
Copyright © 2024,Paragon Industries, L.P.
“Custom and standard Kilns and Industrial Furnaces for ceramics, pottery, heat treating, enameling,dentistry, laboratory, and glass fusing.Better Designed Kilns from Paragon Industries!"
on:
